Residential Plumbing Rough-In Inspection Checklist

Creating a “Residential Plumbing Rough-In Inspection Checklist” in eAuditor Audits & Inspections (or any digital inspection tool) involves breaking down the key aspects of plumbing rough-in based on local building codes, safety standards, and best practices. Below is a detailed checklist for a residential plumbing rough-in inspection that can be used in eAuditor Audits & Inspections:

Residential Plumbing Rough-In Inspection Checklist

1. General Information

• Inspector Name:
• Inspection Date:
• Project Address:
• Permit Number:
• Contractor/Plumber:
• Weather Conditions:
• Job Number:

2. Plumbing Rough-In Overview

• Has the rough-in work been completed according to the approved plans?
  ☐ Yes ☐ No ☐ N/A
• Are the correct pipe materials used for each system (water, waste, vent)?
  ☐ Yes ☐ No ☐ N/A
• Is the plumbing system installed according to local building codes?
  ☐ Yes ☐ No ☐ N/A
• Are all pipes properly labeled (hot/cold, drain, vent, etc.)?
  ☐ Yes ☐ No ☐ N/A

3. Water Supply Lines

• Are water supply lines installed in the correct locations?
  ☐ Yes ☐ No ☐ N/A
• Are pipes adequately supported at intervals specified by code?
  ☐ Yes ☐ No ☐ N/A
• Are water lines properly insulated where required?
  ☐ Yes ☐ No ☐ N/A
• Is the correct pipe size used for water supply (main, branch lines, fixtures)?
  ☐ Yes ☐ No ☐ N/A
• Is the pressure test of water supply lines completed and passed?
  ☐ Yes ☐ No ☐ N/A
• Are shut-off valves installed in accessible locations?
  ☐ Yes ☐ No ☐ N/A

4. Drainage and Waste Lines

• Are waste and drain lines installed according to plans?
  ☐ Yes ☐ No ☐ N/A
• Are pipes correctly sloped (typically 1/4 inch per foot for horizontal runs)?
  ☐ Yes ☐ No ☐ N/A
• Are the correct pipe sizes used for each drain line (toilets, sinks, showers, etc.)?
  ☐ Yes ☐ No ☐ N/A
• Are traps and vents properly installed?
  ☐ Yes ☐ No ☐ N/A
• Is a leak test (water or air) of waste and drain lines completed?
  ☐ Yes ☐ No ☐ N/A
• Are cleanouts installed in accessible locations per code requirements?
  ☐ Yes ☐ No ☐ N/A

5. Venting System

• Are vent pipes installed according to code (stack vents, branch vents)?
  ☐ Yes ☐ No ☐ N/A
• Are vents sized correctly based on fixture unit load?
  ☐ Yes ☐ No ☐ N/A
• Are vent pipes properly supported and spaced?
  ☐ Yes ☐ No ☐ N/A
• Is the venting system free from obstructions and blockages?
  ☐ Yes ☐ No ☐ N/A

6. Fixture Placement & Mounting

• Are the locations of all fixtures (sinks, toilets, tubs, etc.) marked according to plans?
  ☐ Yes ☐ No ☐ N/A
• Are the rough-in measurements for fixture drains and water lines correct?
  ☐ Yes ☐ No ☐ N/A
• Are pipe stubs in correct positions for future fixture connections?
  ☐ Yes ☐ No ☐ N/A
• Are water lines for each fixture type (hot and cold) positioned properly?
  ☐ Yes ☐ No ☐ N/A

7. Gas Lines (If Applicable)

• Are gas lines installed according to the plan and local codes?
  ☐ Yes ☐ No ☐ N/A
• Is the gas pipe material appropriate for the system?
  ☐ Yes ☐ No ☐ N/A
• Are shut-off valves installed and accessible?
  ☐ Yes ☐ No ☐ N/A
• Has a pressure/leak test been performed on gas lines?
  ☐ Yes ☐ No ☐ N/A

8. Water Heater Rough-In (If Applicable)

• Is the water heater location roughed-in according to plans?
  ☐ Yes ☐ No ☐ N/A
• Are the necessary hot and cold water lines run to the unit location?
  ☐ Yes ☐ No ☐ N/A
• Is the venting (if gas) or electrical supply (if electric) prepared?
  ☐ Yes ☐ No ☐ N/A

9. Code Compliance

• Is the rough-in inspection ready for local building department inspection?
  ☐ Yes ☐ No ☐ N/A
• Are any code violations or issues identified?
  ☐ Yes ☐ No ☐ N/A
• Comments on any code violations (describe issues and recommended corrections):

10. Additional Notes & Comments

• Notes or comments on inspection findings: ☐ Yes ☐ No ☐ N/A

11. Inspection Sign-Off

• Inspector Signature:
• Date:
• Contractor/Plumber Signature:
• Date:

How to Use in eAuditor Audits & Inspections

1. Create a New Template: Open eAuditor Audits & Inspections, go to “Templates,” and click “Create New Template.”
2. Add Checklist Sections: Break the form into sections like “General Information,” “Water Supply Lines,” etc.
3. Input Fields: Use text fields, checkboxes, dropdowns, or signature fields where needed.
4. Attachments: Optionally, allow photo documentation for sections where visual verification is needed.
5. Scoring (Optional): If required, assign pass/fail or numerical scores to individual sections for overall inspection grading.

This checklist ensures that all critical areas of a plumbing rough-in are checked, and using it in eAuditor Audits & Inspections helps ensure a thorough, standardized inspection process.